EZo Cycle

EZo Cycle Coventry mobile workshop helping locals with cycle maintenance and upgrades. Fully qualified mechani To stand out from the crowd! Appointments only.

eZo cycle is mainly focussed on bicycle servicing/maintenance, Reimagine bike builds, cycle clothing and bikes from Europe. We cannot show everything that is available on Facebook, but will regularly highlight interesting stuff that is available. We act as a purchasing servicing on behalf of cyclists to get the right gear they like. We specialise in international shipping too, so getting your excl

usive gear for the next ride is possible. Get in touch by messaging us through FB or email via [email protected].

13/04/2026

Same Spot... Years apart

Today we rode passed a spot I took a picture from around 45 years ago, got Frances to take a recreated picture.

02/03/2026

Wheel build: Almost 3 years old now these wheels, still spinning flawlessly. DT swiss G549db rims built o to Bitex hubs with Shimano Rotors and cassette. Bearings not changed yet.

This bike is used on an urban commute everyday and weekends too.

Need a set? Get in touch

26/01/2026

Trek Rail 5 rear linkage service:

Tried out the Lebycle bearing puller but it was not suitable for odd shaped frames, which most full suspension bikes are. Designed with curves for the look not serviceability. So needed to use the Enduro Bearings kit instead. The Noble wheels bearing puller and even punch and hammer for certain bearings. This job can be tough.

But once the new set of bearings are put in, courtesy of ,the rear linkage comes alive. There was a knocking my client noticed and it turns out a spacer in the main pivot was missing.

City on Fire: en route to Breakfast club this morning
17/12/2025

City on Fire: en route to Breakfast club this morning

12/12/2025

SON dynamo front wheel rebuild with Campag Levante rim. Light installation.

SON edelux lights are brill but the Brother Kepler frame was not ideal for this. Bike packing bike with mudguard was not fully designed to have dynamo light setup. The fork had a port at the bottom for the wire to be internal but no port higher up for the wire to come out. The mudguards used a bolt to hold the top up and had a big rubber and steel washer to hold it tight without scratching the fork or mudguard. However it stopped the wire coming out to the light mounted on the fork crown. So I cut a channel out of the rubber washer to allow the wire through between the crown and washer. One light solved. Also had to cut the coaxial plug from the wire to feed it through the port, then resolder the plug back onto the wire.
Next the rear light arrived, this time the rack version not the seat post one.
The tumble w**d rack has a nice port next to the light mount and wire can run out through the end of the tubing. Nice. But then there was no nice was to run the wire to the front, no ports.
The non intrusive way was to wrap the wire around the top tube. But that looked terrible, but risk of damage. So I had to drill ports into the top tube to internal route the wire. I almost drilled 2 holes on the seat stay to hide more of the wire. But didn't want to drill small tubing.
Had to set the frame upside down to gain position to drill on the underside of the tube. Stepped up the drilling from 2mm to 7mm using 0.5mm increments. Bit of filing with rotary tool to clean up the hole. Then used Di2 wire grommets to hole the wire and stop crap getting in.
Then crimped on some connectors and voila all done.

Really wished Brother had designed this in, hate having to drill a frame to do internal routing but needs must. Turn out nice though. Had to use some coloured tape to hold the wire between the rack and top tube, but heyho.

Öhlins in the sun
11/12/2025

Öhlins in the sun

2025 World Championship Ironman 70.3 done.Well done to for coming in top 1/3 overall, even with stomach cramps on the r...
09/11/2025

2025 World Championship Ironman 70.3 done.

Well done to for coming in top 1/3 overall, even with stomach cramps on the run.

Bike performed outstandingly.
It's a wrap

Full bike prepped: Argon18 E119 Tri prepped and ready for Ironman 70.3 World Championship Marbella
08/11/2025

Full bike prepped: Argon18 E119 Tri prepped and ready for Ironman 70.3 World Championship Marbella

Address

45 Southbank Road
Coventry
CV61EZ

Opening Hours

Monday 9am - 6pm
Tuesday 9am - 6pm
Wednesday 9am - 6pm
Thursday 9am - 6pm
Friday 9am - 6pm

Telephone

+447710301511

Website

Alerts

Be the first to know and let us send you an email when EZo Cycle posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to EZo Cycle:

Shortcuts

Share

Category