Richards Racing

Richards Racing Sharing our passion of racing and helping you with your racing and driving needs. Call to schedule an appointment.

I didn't take the best pictures, but beyond excited for this part of the build to be done and moving forward. Thank you ...
04/13/2022

I didn't take the best pictures, but beyond excited for this part of the build to be done and moving forward. Thank you Chaz Ramsey for knocking this out of the park! Chaz normally fabricates dune buggies from the ground up, but he got out of his comfort zone, became a contortionist inside my car and completed this challenge to ensure my future safety. I should be bringing it back home this next week and will of course have more pictures then.

Pro tip when breaking down a driveshaft to replace u joints and carrier bearings...get the torch and air hammer out in t...
04/08/2022

Pro tip when breaking down a driveshaft to replace u joints and carrier bearings...get the torch and air hammer out in the beginning to not having to get them out middle of project 👌😎🤣 made quick work...now clean up and reassembly..

Which picture of Sam Richards's talon leaking looks better? 💁‍♂️🤣
04/01/2022

Which picture of Sam Richards's talon leaking looks better? 💁‍♂️🤣

Little roll cage progress update on my Eclipse.Was a good solid day of welding peices up.Thanks Chaz the contortionist f...
05/09/2021

Little roll cage progress update on my Eclipse.
Was a good solid day of welding peices up.
Thanks Chaz the contortionist for all the work put in 👨‍🏭👌

An update post of a weekend of some good progress at Chaz's Fabrication shop. Got the transmission tunnel areas prepped,...
02/01/2021

An update post of a weekend of some good progress at Chaz's Fabrication shop. Got the transmission tunnel areas prepped, rear brace tacked in, rear lateral bars cut notched and strapped in place, seat brace bar put in place, tacked the main hoop and cut the roof bar to fit. A couple more weekends and should be welding it all up.
Thanks Chaz for all the solid work on this project! 👨‍🎨👨‍🏭👌
Thank you to all the friends, family, and sponsors making this dream a reality. Starting to look a little more of what its going to be 😎

When you have supportive friends 😎👌 someone's trying to get a top fan badge again 😂
01/25/2021

When you have supportive friends 😎👌 someone's trying to get a top fan badge again 😂

Finally was about to start working on my car's cage at Chaz's Fabrication shop this weekend. Made some pretty good progr...
01/25/2021

Finally was about to start working on my car's cage at Chaz's Fabrication shop this weekend. Made some pretty good progress for 2 days of work. Prepped the floor spots on the chassis, cut steel plates, removed more chassis material from the rear of the car to make room, got a couple of the plates hand formed in place and welded, got the main hoop and roof bar measured and bent. Have a good gameplan for the rest of the project and should be hitting it hard again this next weekend! Very excited with how this is turning out and its next stages.
Thank you Chaz! Doing a stellar job on this so far! 👌👨‍🏭👨‍🎨
Be sure you have your Richards Racing page settings set to "see first" to keep up with the updates on this project!

A late post, but I wanted to give a shoutout to Chris Crossman's machining for helping me out with the car and the first...
01/13/2021

A late post, but I wanted to give a shoutout to Chris Crossman's machining for helping me out with the car and the first official sponsor for the old street car.
I bought these wheel spacers and the inner lip wouldn't fit over my hubs just barely. I messaged him the specs I needed them opened up and he quickly got them turned on his lathe and fitting nicely 👌

My street car 99 auto Mitsubishi Eclipse took its first maiden voyage to Chaz's Fabrications today. Unfortunately been w...
12/28/2020

My street car 99 auto Mitsubishi Eclipse took its first maiden voyage to Chaz's Fabrications today. Unfortunately been waiting for material for some time and excited to see this through 😎👌

Figured I would update you guys. Made a little progress this weekend..not always sure if it is forwards or backwards 🤷‍♂...
09/14/2020

Figured I would update you guys. Made a little progress this weekend..not always sure if it is forwards or backwards 🤷‍♂️🤣. Thank you Dad, Samantha, Brian and James Smith for giving me a hand with these projects.
#1 Put the front fenders on to center up the carbon fiber hood and install hood pins.
#2 dropping the rear subframe, cleaning her up and installing some new rubber to replace a torn differential bushing.

Finally getting this turbo for the eclipse back together
09/06/2020

Finally getting this turbo for the eclipse back together

Address

Wichita, KS

Telephone

+13162589008

Website

Alerts

Be the first to know and let us send you an email when Richards Racing posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Richards Racing:

Shortcuts

Share

Category