Quarter Minute Arms

04/13/2026

Customer feedback over the past few weeks from some 6GT barrels we cut in-house for them. Same caliber, different blanks, but with comparable results across the board. We've been so busy with barrel work since we brought everything in house that we haven't even been able to take it live on the website. For that, I am EXTREMELY appreciative of our awesome customers and friends who have trusted me!

With that said, give us a shout if you want to get on the list, whether you want an economic button option or a cut blank done.

03/05/2026

Come see us tomorrow at . We'll be set up all afternoon showing off product, doing whisper pickle demos, and just shooting the s**t before the match this weekend. We'll be on site all weekend as a sponsor and participate. You can even come watch me miss by literal mils during the match with the first outing of my 223 stick shift😆.

02/17/2026

The guys at MTE have been good friends of ours for a few years now and a great source of knowledge throughout the years. These are the absolute best handguards and barrel nuts out there for precision and stability. Get with us if you need one, or go check the MTE site directly. 👌👌👌

02/16/2026

For you PRS Sportsman, NRL, and team match guys, here's a fresh build we just finished up. Coming in at 6.8lbs with mag in and 7.7lbs with a R65K.

- Sidewinder action (aka Defiance Ruckus Hunter)
- Element Magnesium chassis
- grip
- trigger
- 50/50 Nickel carbon blank for better heat dissipation without POI shift.
- chambered by Quarter Minute Arms
- MDT mags

My lightweight 6.5CM shooting could use some work😁, but I'm happy with the initial results from testing this setup out with factory Hornady.

02/08/2026

Check the link below for an overview on our "PBR" line from our friends with a breakdown on specs and its capabilities for a sub 1️⃣k build. Feature rich, but without the price tag to match.

https://www.instagram.com/reel/DUg-kuQgJdc/?igsh=NGoyZnJ6b3d4Zmpm

01/30/2026

You all swarmed me with questions about it yesterday, and here it is! A sub five bill can from one of the best and most proven manufacturers in the whisper pickle business. Same performance that KGM is known for, but with a blue collar price tag.

Product Highlights:

Duty-rated down to 10.3” barrels. Constructed of hardened stainless-steel.
Dedicated 5.56/.223 diameter bore.
1/2x28 direct thread rear mount
Pre-drilled pin & weld hole. (May be P&W on a 12.5-inch barrel for an overall length greater than 16 inches).
High gas-flow design with a shrouded and vented end cap.
Available in BLK or FDE Cerakote.
MSRP: Fo hunnit and twinny figh 😉

01/30/2026

This is going to be an awesome new release from our friends at KGM. We have some on order already, so keep an eye out. If you're trying to get the best bang for your buck on a carbine can, then this will be a no-brainer.

⚡️Coming Tomorrow⚡️
Nothing Missing. Nothing Extra.

01/30/2026

Huge shoutout to Quarter Minute Arms for helping out this year! Go check him out!

01/23/2026

If you're at Shot Show, go check out my friends at HIPERFIRE . Best triggers out there, in my opinion. Might even see my name on a couple of the builds in this video.

01/21/2026

I had a great time sponsoring the Onslow Predator Challenge this past weekend. I was able to connect with a lot of new faces and learn a little more on the predator hunting side of things. We donated a couple of the first barrels cut in-house (more on that later). This was a VERY professionally run event by . We'll be on board for it next year again, for sure.

12/16/2025