01/30/2026
RC Drag Racing class rules
Pro Stock
-Class is designed for the Traxxas drag truck, Losi camaro and DR10
Challenger, but you may build your own using the above three platforms.
-Short course rear motor base build from factory.
-Stock 2wd short course rear motor chassis, no carbon fiber chassis plates permitted.
- Wheelbase of up to 13.5”
- RTR factory chassis is permitted as long as it has
- Factory OEM Transmission
- Axles and steering linkage must be interchangeable with stock vehicle.
-Suspension:
-Must have four shocks each controlling a corner of the car as it was designed as.
-Tires:
-Any rubber tires of foam insert style permitted, No o-ring front tires permitted.
-Motor and ECS is limited to stock production KV from traxxas drag truck, Losi Camaro and DR10 car.
-Wheelie bars permitted.
-Body: Any
-Controller: Any
-Battery:
-Any 2 cells battery permitted. 8.44 volts max.
4.54 lbs 2060 gram minimum weight
-NO AVC, TSM OR OTHER GYRO STEERING ASSIST IS NOT PERMITTED.
——————————————-
Outlaw VXL
-Same as Street Eliminator except:
-Motor and ESC restricted to either a Traxxas Velineon 3500 motor and VXL-3S ESC (Drag Slash),
Reedy 3300 Motor and SC600-BLESC (DR10) or Spektrum 100a ESC and Spektrum 6500KV motor (Losi 22S).
-You can interchange the combo, meaning a Traxxas ESC and Reedy Motor, or Traxxas Motor and Reedy ESC,
or Traxxas ESC and Spektrum motor etc.
Wheelie Bar Allowed
Any body Allowed
————————————
Street Eliminator
-2wd only 12-13.5” wheelbase, no 4wd or 4wd to 2wd conversion allowed.
-Motor: any commonly available 10th scale motor allowed
-Esc: any allowed . Full boost and turbo allowed
-Battery: any commercially available 2 cell lipo allowed. Hard case not required and
battery must use connector or bullet plugs. No hardwiring, single pack only no multi pack
plugged in parallel. Also battery must be fastened in car with some device over the top of
battery to secure . Example: tape ,straps or anything that goes over the top to secure the battery.
2 cell 8.44 maximum voltage if over voltage you will run it down to 8.42
-Tires: commercially available rubber foam insert style tires. Treaded or slick. No oring
fronts and may be ran without foam.
-Burnout : is optional but if a burn out is performed it must be done in designated area.
-No burnouts outside of area or results in DQ
-Shocks : must have 4 shocks with one being on each corner of the vehicle and be connected
to hinge pin arms on all 4 corners.
-Transmission: must use 3-5 gear trans. No belt or link conversion allowed
-Minimum weight: 2060 grams ready to run
-Wheelie bar : 1.5” wheel diameter maximum, 14” from rear axle to end of
wheelie bar including parts or wheels
-Body: must be realistic looking street car / pro mod body coverall 4 tires. Wheel wells must
expose half the tire from side view or in the case of some bodies that have a molded in wheel
well like the 57 Chevy looking bodies they can be cut on body line and be legal.
-Wings and things: rear wing cannot extend more than 3” past rearward most part of body.
Supplied factory rear spoiler may be ran in intended form. Front splitters 1/2” maximum tick out.
-You can remove the molded wing nothing more. (For clarity you can cut right against the
scallops in a single smooth arc cut)
-Bodies with no mold line the body must be at least 2” past the rear glass.
-Rear body cut outs: rear bumper/valance may be cut out. Must retain rear quarter panels
and truck lid. Maybe cut to prevent rear tire tuck but subject to race directors discretion.
-Body holes: 4 allowed 1/2” max diameter for body mounting. Any other hole must be covered
with tape or bolt. No window cutouts allowed.
-Tire prep: is allowed
-No gyros or steering assist devices or receivers allowed. No TSM or AVC receivers allowed.
——————————————
Bracket Class
-All RC electric cars 2wd and 4wd
-Dial in handicap start
-You must announce your dial in before you stage.
-It is your responsibility to make sure your dial in is correct before your pass.
-Max ET 3.5 seconds
-Must use rubber tires
-NO AVC, TSM OR OTHER GYRO STEERING ASSIST
